If you are reading this then I’m sure you have been looking for how to replace a bulb socket. Well, replacing a bulb socket may sound technical or something only technically inclined people can do. Even though that might be true, with our guide on how to replace a bulb socket, we’ll take you through the process of replacing a bulb socket which can be done within few munites.
Although bulb sockets are of different types, be that as it may, the same process can be applied when removing or replacing any type of bulb socket. So, if you ready to know how to replace a bulb socket, then let’s get started.
Choosing the Right Replacement Socket
Light bulb sockets arrive in a gigantic scope of sorts and styles and are intended for explicit uses and bulb wattages. Supplanting the attachment on open-air or indoor installation is comparative, however, it’s essential to utilize the correct attachment for the apparatus. Outside sockets are commonly more vigorous than indoor sockets and frequently have unique highlights for dampness or climate obstruction. For an installation, pick an attachment that seems to be indistinguishable (or almost indistinguishable) to the first and has a similar most extreme wattage rating.
Tools and Supplies You Will Need
- Ladder (as needed)
- Non-contact voltage tester
Instructions to Follow
Turn Off the Power
Switch off the power to the circuit that you’ll be taking a shot at by turning off the suitable breaker in your home’s electrical administration board.
Test for Power
Utilize a non-contact voltage analyzer to check for power in the light attachment. Expel the light from the awful attachment, and contact the test of a non-contact voltage analyzer to the metal tab inside the attachment. Flip the light switch and test the attachment once more. The analyzer ought not to illuminate for either test.
The purpose behind testing with both switch positions is on the grounds that a few switches (like three-way switches) can be on or off in either position.
Remove the Globe
Expel the globe from the installation. The globe might be held by inward cuts, screws on the external ring of the installation, or a retainer nut on the base of the globe. Hold the globe in one hand while relaxing the screw or nut with the other. Put the globe in a safe spot until you are ready to use it again.
Loosen the Fixture and Test for Power
Unlock or evacuate the mounting screws verifying the installed base to the electrical box in the divider or roof. Cautiously pull the apparatus away from the container without contacting any wires. Test for power again by contacting the test of the voltage analyzer to every one of the installation wires and the majority of the wires in the case. The analyzer ought not to illuminate; on the off chance that it does, come back to the administration board and switch off the right breaker, at that point retest the wires to affirm the power is off.
Disconnect the Wiring
Bend the wire connector (wire nut) counterclockwise and expel it from each arrangement of wires, at that point separate the wires. Separate the ground wire from the case or installation mounting lash, as material. Bring the apparatus down and place it on your workbench or table. Force the dark and red wires from the awful attachment through the gap in the apparatus with the goal that the attachment can be evacuated.
Remove the Socket
Look inside the attachment and find the Phillips screw (or screws) holding the attachment to the apparatus. On the other hand, the attachment might be held by a holding nut at the back of the apparatus or bulb lodging, or there might be a screw and a nut. Expel the screw or nut with a screwdriver or pincers, as applicable. Take off the attachment from the apparatus, however, keep the screw as well as a nut on the off chance that you need it for the new attachment.
Install the New Socket
Fit the new attachment into the apparatus in the situation as the first, and secure it with the screw as well as the nut. Be mindful so as not to fix excessively, as attachments can be delicate.
Reinstall the Fixture
Keep the apparatus down up to the divider or roof box and interface the wires as in the past, utilizing a similar wire nut. Dark wires integrate under one wire nut, and white wires integrate under another. Additionally reconnect the ground wire, as applicable. Mount the apparatus with its mounting screws. Make sure that no wires are projecting from the installation base. You would prefer not to squeeze an electrical wire.
Clean and Install the Fixture Globe
Clean the globe (this is advantageous while it’s down) and reinstall it onto the apparatus. Screw a light into the new attachment.
Turn On the Power
Turn on the breaker in the breaker box and test the apparatus for ordinary activity.
What are the 3 types of light bulbs?
Incandescent lights are the customary bulbs with which we’re all recognizable. They cast a warm sparkle, however, are the least effective, and they should be supplanted frequently. Utilize an Incandescent bulb when you need a cozier impact or need to feature the genuine nature of the shade.
Halogen bulbs are more productive than incandescent bulbs – they give 25 to 30 percent all the more light utilizing a similar measure of power. Nonetheless, they transmit a more white light, so they’re more qualified for workplaces, kitchens, or lights with warm-color shades. Additionally, they consume at an extremely high temperature, so don’t utilize one out of an area where you may unintentionally hurt yourself.
CFL (Compact Fluorescent Light) Bulbs
CFLs are the most productive, and they’re accessible in a winding or customary shapes. The bulbs last any longer than customary radiant, and they utilize less power as well. In any case, similar to an incandescent lamp, they will, in general, produce a virus light, so they’re most proper behind shades that will offset their brutality. They likewise contain mercury, so take care when you’re dealing with and discarding them.